Does MBUS have to be in COM2 for nk_calc to work? - GSM-Forum

philkho · 03-04-2002, 09:13

It does not work on my pc. I set up nk_calc to use com1 and when I run nk_calc, it just shows me the main screen and when I press f1, f2, or f3, nothing happens? What seems to be the problem? Thanks. By the way, I'm running it under win98. Thanks!

Ice Dragon · 03-04-2002, 09:22

Encountered that one. What I did was restarted my Win98SE, (Shut down computer and pressed the reset button). Tried again and it works.

Sometimes, I have to check my MBUS cable. Don't use the autoswitching MBUS/FBUS. With my autoswitching, I just disconnected the FBUS wires and leave the MBUS and ground wires connected.

Regards...

J · 03-04-2002, 13:43

I had the same problem, seems like the software does not like autoswitching cables, just take off the FBUS, and all should be fine!!

FRANCK13 · 03-04-2002, 14:07

Same in my laptop, i wait .

i restard in safe mode , and it's work very good with my cable fbus/mbus.
thanks

Chawek · 03-05-2002, 05:39

Hi!
I have dual fbus/mbus cable that i have produced myself, and nk_calc and other programs works 100% on it.
I know that mass produced fbus/mbus cables don't works so good.

Best regards.

03-05-2002, 06:01

If you have modem instaled or other hardware that uses com ports, it likely you've get in trouble. Just press ctrl key while system is booting and choose "safe mode"...

03-04-2002, 09:13	#1 (permalink)
philkho Crazy Poster Join Date: Feb 2001 Location: Manila, Philippines Posts: 58 Member: 3367 Status: Offline Thanks Meter: 0	Does MBUS have to be in COM2 for nk_calc to work? It does not work on my pc. I set up nk_calc to use com1 and when I run nk_calc, it just shows me the main screen and when I press f1, f2, or f3, nothing happens? What seems to be the problem? Thanks. By the way, I'm running it under win98. Thanks!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Does anyone have Universal box in stock?	James_S	Universalbox	0	01-15-2007 23:04
does anybody have lang 0011 or 000D for T720G_05.08.81R?	alexzzander	Motorola P2k	0	01-25-2004 01:10
Does anybody have the Active Desktop Application for 7650?	kingofhearts	WD2 & APE (Symbian Phones)	5	03-04-2003 00:55
Does anyone have info about Samsung R200/A300 unlock... Im working on this	smoother	VLSI, Conexant, Skyworks and Old Models	6	11-03-2001 11:05

03-04-2002, 09:22	#2 (permalink)
Ice Dragon Freak Poster Join Date: Feb 2001 Location: Bacolod, Philippines Posts: 313 Member: 3360 Status: Offline Thanks Meter: 4	Encountered that one. What I did was restarted my Win98SE, (Shut down computer and pressed the reset button). Tried again and it works. Sometimes, I have to check my MBUS cable. Don't use the autoswitching MBUS/FBUS. With my autoswitching, I just disconnected the FBUS wires and leave the MBUS and ground wires connected. Regards...

03-04-2002, 13:43	#3 (permalink)
J Freak Poster Join Date: May 1999 Location: London Posts: 393 Member: 47 Status: Offline Sonork: 1583023 Thanks Meter: 15	I had the same problem, seems like the software does not like autoswitching cables, just take off the FBUS, and all should be fine!!

03-04-2002, 14:07	#4 (permalink)
FRANCK13 Junior Member Join Date: Oct 2001 Location: in internet Posts: 33 Member: 7016 Status: Offline Thanks Meter: 0	Same in my laptop, i wait . i restard in safe mode , and it's work very good with my cable fbus/mbus. thanks

03-05-2002, 05:39	#5 (permalink)
Chawek Insane Poster Join Date: Feb 2002 Location: Poznan - Poland Age: 41 Posts: 75 Member: 9339 Status: Offline Thanks Meter: 0	Hi! I have dual fbus/mbus cable that i have produced myself, and nk_calc and other programs works 100% on it. I know that mass produced fbus/mbus cables don't works so good. Best regards.

03-05-2002, 06:01	#6 (permalink)
legija Guest Posts: n/a Member:	If you have modem instaled or other hardware that uses com ports, it likely you've get in trouble. Just press ctrl key while system is booting and choose "safe mode"...